Files
LithosAnanke/v4/include/v4/exec.h
T
Claude e1b731f444 feat(v4): Phase 7 Task 3b -- compudynamics on the 32 F18 opcodes as on the words, behind OPCODE_PHYSICS (#189)
Captain Bob, 2026-11-14: "we're supposed to be working on f18 opcode as well as our composed f18
dictionary"; ruled every loop on both, "and an easy revert if opcodes are too granular".

- The engine: a hook at retire (exec.h on_retire), as Part A's at call; NULL unless set. test_exec.c.
- The mesh: 32 opcode records per node, an opcode window, opcode transitions under L4; at every retired
  instruction decay at the opcodes' own slope, heat, temperature, the window, the transition; in each cycle
  all 32 cooled, the opcode window's service, inference on its heat. L8 scores from the words and its gates
  govern both; the tick stays paced by word calls. The window is now one type for words and opcodes.
- The revert: OPCODE_PHYSICS (Kconfig.physics, default y; the kernel's flags) -- 0 and the opcodes are
  counted and charged to the Stadium as in Phase 1. make -C v4 mesh-boot-noop builds and tests it.
- Tests first: test_mesh_boot.c 77 checks as built, 86 with pipelining on, 74 with the revert.
- Measured on amd64, back to back: 219 s on, 196 s off (+12% under TCG). Both boots' logs labelled.
Not pushed (held to the end of Phase 7).

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_017RzZgrf7V7Zk2iczBXDRbm
2026-11-14 00:29:08 +00:00

91 lines
4.3 KiB
C

/* SPDX-License-Identifier: LicenseRef-Starship-1.0
* Copyright (c) 2023-2026 Robert A. James
*/
/* exec.h -- instruction execution for v4.
*
* DECOMPOSITION.md section 1.2: "Slots execute left to right." A branch
* (jump, call, next, if, -if) takes its target from all bits to the right of
* its slot and replaces the same low bits of P (page-relative). Branches are
* legal in slots 0-3 only. Nothing to the right of a branch executes, taken
* or not, because those bits are its address.
*
* Section 1.4: "Every retired instruction increments that opcode's heat counter
* and advances the anti-clock; every `call` increments the heat counter of its
* target. None of this costs an instruction." A call's target is counted by
* whoever runs the node, through the hook below (ENGINE.md step 3; plan
* 2026-10-20, Task A1, #189): the kernel keeps a word's accounts. The engine's
* own per-call-target table, a stand-in, is gone.
*
* The node owns P, A, B, the stacks and memory; heat and the anti-clock are
* separate physics state (section 7 names them as registers).
*
* THREE POINTS THE SPEC LEAVES TO THE F18, and which this model takes from it:
*
* - `ex` ends the word, like `;`. P has been replaced, so the remaining
* slots belong to a word that is no longer the current one.
* - `unext` restarts the *already fetched* word at slot 0. It does not
* refetch and does not move P, so `@p` and `!p` inside a unext loop step
* through the words that follow the loop word. When R reaches 0 the loop
* ends and execution continues with the slot after `unext`.
* - `+*` shifts T arithmetically (sign bit kept). Section 1.3 says only
* "shift T:A right one bit"; D-3 says plain F18 semantics.
*
* A branch opcode in slot 4 or 5 is outside the spec. The model does not trap
* it: it applies the 7- or 2-bit target the layout formula gives.
*/
#ifndef V4_EXEC_H
#define V4_EXEC_H
#include "v4/heat.h"
#include "v4/iword.h"
#include "v4/node.h"
/* Called at `call` once the return address is pushed and before P moves to the
* target (so P is still the return address). NULL: no hook. */
typedef void (*v4_call_hook)(void *ctx, v4_node *n, v4_cell target);
/* Called when an instruction retires, after HEAT-OP counts it, with its opcode (0..31): compudynamics on the
* opcodes (#189 Phase 7, ruling 7). NULL: no hook. */
typedef void (*v4_retire_hook)(void *ctx, v4_node *n, unsigned op);
typedef struct {
v4_uheat_t anticlock;
v4_call_hook on_call; /* reset leaves NULL */
void *on_call_ctx;
v4_retire_hook on_retire; /* reset leaves NULL */
void *on_retire_ctx;
/* A node blocked at its port in the middle of an instruction word
* (node.h) goes on, when it has been served, from the slot after the
* store: the word and the slot are kept here meanwhile. */
int resume;
v4_iword resume_iw;
unsigned resume_slot;
unsigned resume_faults; /* n->faults when it blocked: a fault since then means P is a handler and the rest of the word is abandoned */
} v4_exec_state;
void v4_exec_reset(v4_exec_state *es);
/* Execute one instruction word: fetch at P, advance P, run the slots left to
* right until the word ends. A unext loop runs to completion inside one call,
* so the call does not return while R is nonzero at a `unext`. Returns the
* number of instructions retired.
*
* FAULTS (node.h; D-14 and D-16). Before an opcode runs, the stacks must
* hold what it takes -- a T or S it only reads counts -- and have room for
* what it leaves; and an address it uses, or P at the fetch, must be inside
* node memory. If not, that opcode and the rest of the word do not execute,
* both stacks are emptied, and P is that kind's word of the node's fault
* table on return. With no table the node stops, and this does nothing and
* returns 0 from then on. */
unsigned v4_exec_step_word(v4_node *n, v4_exec_state *es, v4_heat *h);
/* Execute a single opcode. The branch opcodes read their target from `w` and
* `slot`; every other opcode ignores both. `unext` here only updates R; the
* restart is v4_exec_step_word's. A value above 31 does nothing and retires
* nothing. */
void v4_exec_op(v4_node *n, v4_exec_state *es, v4_heat *h,
unsigned op, v4_iword w, unsigned slot);
#endif /* V4_EXEC_H */